 |
 |
 |
|
Benjamin Moore ben Interior Acrylic Latex Paint Flat W625 is an acrylic blended latex flat coating designed for application to a wide variety of interior surfaces. Produces a decorative and uniform flat finish with excellent hiding.
Colors Available: White, Available in any Benjamin Moore Color
Gloss: Flat
Cleanup: Water
Resin Type: Proprietary Acrylic Latex
Recommended Use: Interior
Recommended For: Destination Paint recommends Benjamin Moore ben Interior Acrylic Latex Paint Flat W625 for newly painted or previously painted wallboard, masonry, or wallpapered surfaces; primed or previously painted plaster, wood or metal, and on new or coated acoustical ceilings.
Surface
Preparation
Surfaces to be painted must be clean and free from dirt, dust, wax, soap, oil, grease, and water soluble materials. Remove any peeling or scaling paint and sand these areas to feather edges smooth with adjacent surfaces. Glossy areas should be dulled. New plaster and masonry must be cured before painting. Apply primer before and after filling nail holes, cracks, and other surface imperfections.
Unpainted Surfaces & Masonry: New
plaster or masonry surfaces must be allowed to cure (30 – 60 days) before priming. All surfaces must be thoroughly brushed with stiff fibre bristles to remove loose particles. Repaint Surfaces: Remove any peeling or scaling paint, and sand these areas to feather edges smooth with adjacent surfaces.
Difficult Substrates: Benjamin Moore offers a variety of specialty primers for use over difficult substrates such as bleeding woods, grease stains,
crayon markings, hard glossy surfaces, galvanized metal, or other
substrates where paint adhesion or stain suppression is a particular
problem. Destination Paint can recommend the right problem-solving Benjamin Moore
primer for your special needs.
WARNING! If you scrape,
sand or remove old paint, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.
Wear a NIOSH approved respirator to control lead exposure. Carefully
clean up with a HEPA vacuum and a wet mop. Before you start, find out
how to protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
Mixing of Paint: Stir thoroughly
before and during use. This product can also be sprayed. Refer to the
chart below for application recommendations. Conditioning with Benjamin Moore
Premium Waterborne Paint Extender 518 may be necessary under certain conditions to adjust open time or spray characteristics.
| | Mild conditions | Severe
conditions
| | | Humid (RH> 50%) with no
direct sunlight & with little to no wind | Dry (RH<50%),
in direct sunlight,
or windy conditions | Brush: Nylon / Polyester
Roller:
Premium Quality
Spray: Airless
Pressure:
1500
-2500 psi
Tip: 0.013-0.017
| No
thinning
necessary | Add 518 Extender
or water:
Max of 8 fl. oz. to a gallon paint
Never add other
paints or solvents. |
Thinning/CleanupConditioning with Benjamin
Moore
Premium Waterborne Paint Extender 518 may be necessary under certain conditions to adjust open time or spray characteristics. Cleanup: Wash
brushes, rollers, and other painting tools in warm soapy water
immediately after use. Spray equipment should be given a final rinse
with mineral spirits to prevent rusting. USE COMPLETELY OR DISPOSE OF PROPERLY. Dry, empty
containers may be recycled in a can recycling program. Local disposal
requirements vary; consult your sanitation department or
state-designated environmental agency on disposal options.
Environmental, Health &
Safety Information
Use only
with adequate ventilation. Do not breathe spray mist or sanding
dust. Ensure fresh air entry during application and drying. Avoid
contact with eyes and prolonged or repeated contact with skin. Avoid
exposure to dust and spray mist by wearing a NIOSH approved respirator
during application, sanding and clean up. Follow respirator
manufacturer’s directions for respirator use. Close container after each
use. Wash thoroughly after handling.
FIRST AID
Eye Contact:
Flush immediately with plenty of water for at least 15 minutes.
Skin Contact: Wash thoroughly with
soap and water. If symptoms persist, seek medical attention. If you
experience difficulty breathing, leave the area to obtain fresh air. If
continued difficulty is experienced, get medical attention immediately.
IN CASE OF SPILL: Absorb with inert
material and dispose of as specified under Thinning/Cleanup.
KEEP OUT OF REACH OF CHILDREN
PROTECT FROM FREEZING
Refer to Material Safety Data Sheet for additional health
and safety information.
MSDS:
MSDS
W626 (English)
TDS:
TDS
W626 (English)
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features At A Glance
Benjamin Moore ben Interior Acrylic Latex Paint Flat W625
- Attractive eggshell finish with very good washability
- Painted surfaces can be washed after two weeks
- Easy application
- Easy clean-up, just use water
- Premium hide and leveling
- Low odor and low VOC even after tinting
|
|
|
|
|
|
|
