 |
 |
 |
|
Benjamin Moore MoorLife Acrylic House Paint Flat N105 is a premium quality, 100% acrylic exterior latex house
paint in a popular flat finish. Benjamin Moore's latest technological improvement,
using 100% acrylic resin and proprietary alkyd technology, provides a
protective exterior coating that will remain looking freshly painted
years after the job is finished. This high solids formula is suitable
for a variety of exterior surfaces and can be applied at a wider
temperature range.
Colors Available: Benjamin Moore® Color Preview® Bases, Brilliant White, Red Brick, Country Redwood, Richmond Bisque, Tudor Brown, Brownstone, Charleston Brown, Platinum Gray, Navajo White, Briarwood
Gloss: Flat
Cleanup: Water
Resin Type: 100% Acrylic Latex
Recommended Use: Exterior
Recommended For: Destination Paint recommends Benjamin Moore MoorLife Acrylic House
Paint Flat N105 for exterior use on masonry surfaces such as stucco, cement and cinder block, as well as on unglazed brick. Benjamin Moore MoorLife Acrylic House
Paint Flat N105 is ideally suited for use on hardboard, vinyl and aluminum siding, wood, shakes and shingles.
Surface Preparation
Surfaces must be clean and free of grease, wax, and mildew. Remove excessive chalk and loose or scaling paint. If previously coated with cement-base water paints, clean by sandblasting. Glossy surfaces must be dulled. Un-weathered areas such as eaves, ceilings, and overhangs should be washed with a detergent solution and/or rinsed with a strong stream of water from a garden hose to remove contaminants that can interfere with proper adhesion. Mildew must be removed by application of Benjamin Moore® CLEAN 318. Caution: Use rubber gloves, work goggles, and protective clothing. For metal surfaces, remove rust. Wipe down with paint thinner to remove surface oils.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
Stir thoroughly before and during use. Apply one or two coats. For best results, use a Benjamin Moore® custom-blended nylon/polyester brush, Benjamin Moore® roller, or a similar product. This product can also be sprayed.
Spray, Airless: Fluid Pressure — 1,500 to 2,000 PSI; Tip .013 - .017 Orifice
Thinning/Cleanup
Thinning is unnecessary, but if required to obtain desired application properties, a small amount of clean water may be added. Never add other paints or solvents. Clean up with warm soapy water. Brushes should be given an additional quick rinse with mineral spirits followed by a second wash in soapy water, then rinsed thoroughly. Spray equipment should be given a final rinse with mineral spirits to prevent rusting.
USE COMPLETELY OR DISPOSE OF PROPERLY. Dry, empty containers may be recycled in a can recycling program. Local disposal requirements vary; consult your sanitation department or state-designated environmental agency on disposal options.
Environmental, Health & Safety Information
Contains Crystalline Silica that can cause cancer when in the respirable form (spray mist or sanding dust).
Use only with adequate ventilation. Do not breathe spray mist or sanding dust. Ensure fresh air entry during application and drying. Avoid contact with eyes and prolonged or repeated contact with skin. Avoid exposure to dust and spray mist by wearing a NIOSH approved respirator during application, sanding and clean up. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling.
FIRST AID: In case of eye contact, flush with water for 15 minutes; for skin, wash with soap and water. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
IN CASE OF SPILL: Absorb with inert material and dispose of as specified under Thinning/Cleanup.
KEEP OUT OF REACH OF CHILDREN
PROTECT FROM FREEZING
Refer to Material Safety Data Sheet for additional health and safety information.
Material Safety Data Sheet (MSDS):
MSDS
N105 EnglishMSDS
N105 Español
Technical Data Sheet (TDS):
TDS
N105 English
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features At A Glance
Benjamin Moore MoorLife Acrylic House Paint Flat N105
- Outstanding hiding
- Covers in one coat provided the surface is in good condition
and the color change is not extreme
- Superior adhesion and excellent resistance to chalking
- Delivers a high-build paint film for excellent durability and
long lasting protection
- Lifetime warranty (see label for details)
- Easy to apply with brush, roller or sprayer
- Soap and water clean up
- Dries quickly
- Resistant to fading, cracking, peeling, blistering, dirt
pick-up, alkali and fumes
- Mildew resistant - Benjamin Moore MoorLife Acrylic House
Paint Flat N105 is specially formulated to
contain agents which inhibit the growth of mildew on the surface of the
paint film
- Low temperature application
|
|
|
|
|
|
|
