 |
 |
 |
|
Benjamin Moore MoorGlo Acrylic House And Trim Paint Soft Gloss N096 is a premium quality, 100% acrylic exterior latex house
paint in a popular soft gloss finish. The unique resin package in the Benjamin Moore MoorGlo Acrylic House
And Trim Paint Soft Gloss N096 provides optimal adhesion,
gloss, and color retention along with long lasting durability. The
result is a protective coating that will appear "freshly painted" for
years to come. Benjamin Moore MoorGlo Acrylic House
And Trim Paint Soft Gloss N096 is suitable
for a variety of exterior surfaces and can be applied at a wider
temperature range.
Colors Available: Brilliant White, Cottage Red, Country Redwood, Heritage Red, Classic Burgundy, Chrome Green, Essex Green, Black Forest Green, Richmond Bisque, Tudor Brown, Charleston Brown, Platinum Gray, Navajo White, Briarwood and Black
Gloss: Semi-Gloss
Cleanup: Water
Resin Type: 100% Acrylic Latex
Recommended Use: Exterior
Recommended For: Destination Paint recommends Benjamin Moore MoorGlo Acrylic House
And Trim Paint Soft Gloss N096 for exterior use on primed or previously painted wood siding, trim, doors, sash, shingles; cured or previously painted masonry such as stucco, cement block construction, poured and precast concrete, and unglazed brick. Ideal for use on aluminum, vinyl, or site primed hardboard siding; and also on previously painted or primed metal.
Surface Preparation
Surfaces must be clean and free of grease, wax, and mildew. Remove excessive chalk and loose or scaling paint. If previously coated with cement-base water paints, clean by sandblasting. Glossy surfaces must be dulled. Un-weathered areas such as eaves, ceilings, and overhangs should be washed with a detergent solution and/or rinsed with a strong stream of water from a garden hose to remove contaminants that can interfere with proper adhesion. Mildew must be removed by application of Benjamin Moore® CLEAN 318. Caution: Use rubber gloves, work goggles, and protective clothing. For metal surfaces, remove rust. Wipe down with paint thinner to remove surface oils.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
Stir thoroughly and apply with a good quality synthetic bristle brush or medium-nap roller.
Spray, Airless: Fluid Pressure — 1,500 to 2,500 PSI; Tip — .013 - .017 Orifice.
Thinning/Cleanup
Thinning is unnecessary, but if required to obtain desired application properties, a small amount of clean water may be added. Never add other paints or solvents. Clean up with warm soapy water. Brushes should be given an additional quick rinse with mineral spirits followed by a second wash in soapy water, then rinsed thoroughly. Spray equipment should be given a final rinse with mineral spirits to prevent rusting.
USE COMPLETELY OR DISPOSE OF PROPERLY. Dry, empty containers may be recycled in a can recycling program. Local disposal requirements vary; consult your sanitation department or state-designated environmental agency on disposal options.
Environmental, Health & Safety Information
Use only with adequate ventilation. Do not breathe spray mist or sanding dust. Avoid contact with eyes and prolonged or repeated contact with skin. Wear eye protection and gloves during application or sanding. A dust/particulate respirator approved by NIOSH should be worn when sanding or spraying. Close container after each use.
FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air.
IN CASE OF SPILL: Absorb with inert material and dispose of as specified under Thinning/Cleanup.
KEEP OUT OF REACH OF CHILDREN
PROTECT FROM FREEZING
Material Safety Data Sheets available on request from your servicing retailer.
Material Safety Data Sheet (MSDS):
MSDS
N096 EnglishMSDS
N096 Español
Technical Data Sheet (TDS):
TDS
N096 English
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features At A Glance
Benjamin Moore MoorGlo Acrylic House And Trim Paint Soft Gloss N096
- Excellent hide
- Superior adhesion and excellent resistance to chalking
- Lifetime limited warranty (see label for details)
- Excellent flow and leveling
- Easy to apply with brush, roller or sprayer
- Soap and water clean up
- Resistant to fading, cracking, peeling, blistering, dirt pickup,
alkali and fumes
- Mildew resistant - Benjamin Moore MoorGlo Acrylic House
And Trim Paint Soft Gloss N096 is specially formulated to contain
agents which inhibit the growth of mildew on the surface of the paint
film
- Low temperature application
|
|
|
|
|
|
|
