 |
 |
 |
|
Benjamin Moore Fresh Start Acrylic All-Purpose Primer 023 is a premium quality, 100% acrylic interior and exterior
primer formulated for sealing and suppressing most bleeding type
stains: including crayon, graffiti, grease marks, water stains; cedar
and redwood bleed; asphalt, creosote, rust and smoke. In cases of severe
bleeding, a solvent based primer should be used to prevent stains from
reappearing. Benjamin Moore Fresh Start Acrylic
All-Purpose Primer 023 combines many
of the qualities desired in a primer: high hiding, excellent adhesion
(even over chalky surfaces), blister resistance, quick dry, spatter-proof
and minimal odor with excellent flow and leveling.
Colors Available: White*
Gloss: Primer
Cleanup: Water
Resin Type: 100% Acrylic Latex
Recommended Use: Interior, Exterior
Recommended For:
Interior Surfaces: Destination Paint recommends Benjamin Moore Fresh Start Acrylic
All-Purpose Primer 023 for newly painted or previously painted wood, plywood, drywall, ceiling tile, formica, masonite, ceramic tile and cured plaster. Benjamin Moore Fresh Start Acrylic
All-Purpose Primer 023 is an excellent sealer and primer for use under new wall coverings and can also be used as a primer coat over existing wall coverings.
Exterior Surfaces: Destination Paint recommends Benjamin Moore Fresh Start Acrylic
All-Purpose Primer 023 for newly painted or previously painted wood, aluminum and hardboard siding, shingles, shakes, concrete, masonry, brick and metal surfaces.
Additional Information: *May be tinted to light pastels with up to 2.0 fl. oz of Color Preview® colorants per gallon. For best hiding results, tint primer to the approximate shade of the finish coat.
Having trouble picking the right primer? Learn more from the Fresh Start Primer Chart.
Surface Preparation
Surfaces to be painted must be clean, dry, and free of dirt, dust, grease, oil, soap, wax, scaling paint, water soluble materials, and mildew. Remove any peeling or scaling paint and sand these areas to feather edges smooth with adjacent surfaces. Glossy areas should be dulled. Drywall surfaces must be free of sanding dust.
New plaster or masonry surfaces must be allowed to cure before applying base coat. Cured plaster should be hard, have a slight sheen and maximum PH of 10; soft, porous or powdery plaster indicates improper cure. Never sand a plaster surface; knife off any protrusions and prime plaster before and after applying patching compound. Poured or pre-cast concrete with a very smooth surface should be etched or abraded to promote adhesion, after removing all form release agents and curing compounds. Remove any powder or loose particles before priming. Wood substrates must be thoroughly dry. Caution: Smooth planed clapboards or siding must be sanded thoroughly to break the “mill glaze” allowing proper penetration and adhesion.
Difficult Substrates: If the surfaces to be painted exhibit severe tannin or smoke staining, an alkyd based Benjamin Moore primer may be your best choice for conquering these severe conditions. Consult the experts at Destination Paint for further guidance.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Application
Stir thoroughly before and during use. Apply one or two coats.
Paint Application: For best results, use a premium Benjamin Moore custom-blended nylon/polyester brush, premium Benjamin Moore roller, or a similar product. Apply paint generously from unpainted area into wet area.
This product can also be sprayed.
Spray, Airless: Fluid Pressure: 1500 – 2500 Tip: .013 - .017
Thinning/Cleanup
Thinning is unnecessary, but if required to obtain desired application properties, a small amount of clean water may be added. Never add other paints or solvents.
Clean Up: Clean equipment with mineral spirits. Spray equipment should be given a final rinse with mineral spirits to prevent rusting.
USE COMPLETELY OR DISPOSE OF PROPERLY. Dry, empty containers may be recycled in a can recycling program. Local disposal requirements vary; consult your sanitation department or state-designated environmental agency on disposal options.
Environmental, Health & Safety Information
Use only with adequate ventilation. Do not breathe spray mist or sanding dust. Ensure fresh air entry during application and drying. Avoid contact with eyes and prolonged or repeated contact with skin. Avoid exposure to dust and spray mist by wearing a NIOSH approved respirator during application, sanding and clean up. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling.
FIRST AID: In case of eye contact, flush with water for 15 minutes; for skin, wash with soap and water. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
IN CASE OF SPILL: Absorb with inert material and dispose of as specified under Thinning/Cleanup.
KEEP OUT OF REACH OF CHILDREN
PROTECT FROM FREEZING
Refer to Material Safety Data Sheet for additional health and safety information.
Material Data Safety Sheet (MSDS):
MSDS
023 English
MSDS
023 Español
Technical Data Sheet (TDS):
TDS
023 English
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features At A Glance
Benjamin Moore Fresh Start Acrylic All-Purpose Primer 023
- Provides a total latex system, offering excellent resistance to blistering on new construction
- Easy to apply
- Excellent hiding and leveling properties
- Excellent adhesion even over chalky surfaces
- Quick drying
- Spatter resistant
- Minimal odor
|
|
|
|
|
|
|
